{"product_id":"mg34-2-piece-308-blank-barrel-set","title":"MG34 2-Piece .308 Blank Barrel Set (Limited run)","description":"\u003cp\u003eJuly 2026- very limited run made- get em while they last!\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e \/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\u003cbr\u003e\u003cem\u003eWe are also in the process of developing a new style 2 part blank barrel, being made from old MG13 barrels, which will look more like original WWII era blank barrels with the slender center section. \u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003ePlease contact us if you are interested, the more interest, the better the chance of encouraging the run to get done sooner than later. CONACT TROY with KT ALLIED, LLC at tmannn34 @aol.com or (330) 931-1931\u003c\/em\u003e \/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eThis is a complete \u003cstrong\u003e7.62x51 NATO .308 caliber (\u003cspan style=\"text-decoration: underline;\"\u003eNOT\u003c\/span\u003e 8mm) blank\u003c\/strong\u003e fire 2 piece barrel with some additional design features engineered specifically for firing blanks. The kit includes: 1 two part blank barrel, 1 set of 8 various aperture set screw blank adapters, 1 Allen wrench, and 1 booster cone replacement block. \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eThe two piece barrel set up is one of the best ways to blank adapt your full auto or semi-auto MG34. For the gun to cycle, the barrel normally floats within the shroud traveling with the bolt for a short distance before unlocking from the bolt and returning to the forward firing position. \u003cstrong\u003eThe advantage of the 2 piece design is that, rather than moving the entire weight of the full barrel, only the much lighter rear section must travel back with the bolt.\u003c\/strong\u003e This is significantly easier for a blank cartridge to do allowing for better blank adapting. \u003cspan\u003eMore flash, more bang going out of the front of the gun rather than being used up just to operate it. \u003c\/span\u003eOur muzzle cone replacement block is designed to assist the barrel more for blank fire by locking the front of the barrel in tightly and venting gas forward rather than channeling it back towards the barrel. To adjust the back pressure for blanks you simple change out the set screws in the end on the barrel allowing for easy and relatively quick adjustments for various powder loads. \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWe also offer the booster cone replacement piece separately as well as the set of 8 set screws.\u003c\/strong\u003e So if you already use a 2 piece barrel replacing this part should make your MG fire blanks much better. It makes the 2 piece barrel more efficient. \u003cspan\u003ePlease note that when you are using a 2 piece barrel you should NEVER have any kind of restriction in the booster cone. This only makes the 2 piece barrel fight itself! The restriction should be in the forward part of the 2 piece barrel so that all the gas pressure is used to operate the smaller rear chamber piece.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThis item can NOT be shipped internationally - all non-US \u003c\/strong\u003e\u003cstrong\u003eorders will be canceled! \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"text-decoration: underline;\"\u003eINSTALLATION NOTES:\u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlways start your blank adapting tests without any set screw installed!\u003c\/strong\u003e There is a slim chance the blanks you are using may not require any restriction. If the gun does not cycle, move on to installing the blank adapting set screws.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStart with the set screw that has the largest hole in it first!\u003c\/strong\u003e Test fire, If the gun does not cycle, install the set screw with the second largest hole and so on. Ensure the set screw is tightened down before firing. Only install one set screw at a time.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eYou always want to have the set screw with the largest hole possible that still cycles the gun! \u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNever load more than about 4 or 5 blanks on a belt for testing.\u003c\/strong\u003e If the bolt fails to come back far enough to catch the sear the, gun may just keep firing and the trigger would be ineffective to stop it. Failing that, you can generally stop a runaway MG34 easily buy grabbing ahold of the belt, thus preventing it from feeding into the gun.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eUsing the original muzzle cone will just cause the 2 piece barrel to fight with itself and reduce the reliability of your MG!\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003eOnce you install the blank barrel, remove the muzzle cone, REMOVE THE OLD BOOSTER BUSHING, THEN INSTALL THE BOOSTER BUSHING PROVIDED, AND IT SHOULD ENGAGE THE BARREL END.\u003c\/li\u003e\n\u003cli\u003eTHE MUZZLE CONE SHOULD BE ENGAGED ON THE BUSHING, WHICH IN TURN IS ENGAGING THE BARREL- THIS IS WHAT  YOU WANT.\u003c\/li\u003e\n\u003cli\u003eTHE FRONT BARREL SECTION IS BEING PUSHED FORWARD, THE MUZLE AREA IS HELPING TAKE SOME OF THE PRESSURE, SO YOU DONT JUST HAMMER THE INSIDE OF YOUR BARREL JACKET AT THE LARGEST BARREL DIAMETER. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"War's End Shop","offers":[{"title":"MG34 2-Piece .308 Blank Barrel Set","offer_id":46014078615750,"sku":"Blue Bin 1","price":489.0,"currency_code":"USD","in_stock":true},{"title":"MG34 Blank fire Booster Cone ONLY","offer_id":46014078648518,"sku":"Blue Bin 1","price":29.95,"currency_code":"USD","in_stock":true},{"title":"Set of 8 Pre-Drilled Set Screws","offer_id":46014078681286,"sku":null,"price":45.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0187\/4100\/products\/WWII_German_MG43_Mg_34_2_piece_Blank_fire_Barrel_.308_reenacting_WW2.jpg?v=1571438736","url":"https:\/\/www.warsendshop.com\/products\/mg34-2-piece-308-blank-barrel-set","provider":"War's End Shop","version":"1.0","type":"link"}